roger beep board

[patscavalier]

digging though a box of radio stufff i think i found a roger beep board
i think it may be a hygain
but it only has numbers on it and thats all
numbers 3892
6 wires

heres a pic

[Please login or register to view this link]

[Please login or register to view this link]

this what i have

---

September 9th, 2013, 6:57 am

so what wire goes where in a 148
red and black is pos + and neg --

[MDYoungblood]

Okay I am going to take a give it a try, I have never seen or hooked one up like that. I am not a fan of RB's or noise toys. You have the red and black, don't know if it is 8v or 12v needed. These are just guesses so don't take it to gospel, the white is the audio and the green is the trigger (TX). Now the other two they might be for a switch, (momentary contact), since there is a IC on the board it may have a couple different sounds (beeps). As for installing it in a 148, I would say put it back in the box it came out of, like I said, not a fan.

3's

Greg

[sonoma]

sure looks like this roger beep board, even the instructions are there.

[Please login or register to view this link]

[patscavalier]

Okay I am going to take a give it a try, I have never seen or hooked one up like that. I am not a fan of RB's or noise toys. You have the red and black, don't know if it is 8v or 12v needed. These are just guesses so don't take it to gospel, the white is the audio and the green is the trigger (TX). Now the other two they might be for a switch, (momentary contact), since there is a IC on the board it may have a couple different sounds (beeps). As for installing it in a 148, I would say put it back in the box it came out of, like I said, not a fan.

3's

Greg

im not a fan of noise toys
but i dont have a problem with roger beep
i didnt take out of the radio it was in

sure looks like this roger beep board, even the instructions are there.

[Please login or register to view this link]

sort of but not
that one has 4 wires and ine has 6 wires

[sonoma]

if you read the instructions it shows adding 2 wires for a on off switch which would give you 6 wires and the 2 wires on the right side of the bottom pic you have posted looks like the same location on the board where you cut the jumper and put a on off switch in its place. the top pic looks as if it is the location on the top of the pic.

[MDYoungblood]

The boards do look close and I think I am right about the green and white wires. Look at the board where the other 2 wires are and see if it is marked in any way, ie: sw, tb . The "sw" would be for an on/off switch and the "tb" is for talkback, that would be an on/off switch also.

3's

Greg

[sonoma]

The boards do look close and I think I am right about the green and white wires. Look at the board where the other 2 wires are and see if it is marked in any way, ie: sw, tb . The "sw" would be for an on/off switch and the "tb" is for talkback, that would be an on/off switch also.

3's

Greg

it looks very close to me also. all components look to be in about the same location.

[patscavalier]

i have been looking at this closer and i see that the 2 other wires are for a switch
so sonoma you where correct i was missing that point

md it likes light your right

---

September 12th, 2013, 9:05 pm

this thing
i have the red wire to power
the black to ground
the white to pin 1 on the on the little board behind the mic jack
the green to pin 5 on the on the little board behind the mic jack

but no joy
what did i do wrong

---

September 13th, 2013, 12:36 pm

ok after hours of looking on the net
i found this witch is the board i have

[Please login or register to view this link]

now witch is in put and out put
i think the box T and R out put ?????

---

September 14th, 2013, 10:34 am

well after hours of trying i gave up on getting to work
the funny thing was if i left the ground wire off the relay would work when keyed
but if i hook it up it auto keyed the radio
so i put it in file 86 ( trash it )
i still want a roger beep, so im going to look it others

---

September 14th, 2013, 10:36 am

well after hours of trying i gave up on getting to work
the funny thing was if i left the ground wire off the relay would work when keyed
but if i hook it up it auto keyed the radio
so i put it in file 86 ( trash it )
i still want a roger beep, so im going to look it others